Defi Link VSD Concept User Manual download pdf (Page 12)

Opening and ending modes are performed after the ignition key is turned on and off.

Opening mode

Ending mode

■When the Defi-Link Display VSD CONCEPT is used WITHOUT a connection to the Defi-Link System

When the Defi-Link Display VSD CONCEPT is used WITHOUT a connection to the Defi-Link System

①Real Mode

Illumination control

■When the Defi-Link Display VSD CONCEPT is used WITH a connection to the Defi-Link System

②Peak Mode

③Peak Reset Mode

④Special Display Mode

NOTE: If "MPH, °F, PSI" is selected in the

setting of units, data other than

the engine speed is not displayed.

NOTE: If "MPH, °F, PSI" is selected in the

setting of units, data other than

the engine speed is not displayed.

NOTE: When connected to the Defi-Link System, the PEAK button of the D.C.Unit is unavailable.

The actual vehicle speed is displayed digitally and the engine speed is displayed in

the bar section. When the engine speed exceeds the warning value set as the

tachometer warning1 in the setting of tachometer warning, the green LED lights up.

When it exceeds the tachometer warning2, the green and red LEDs blink.

Pressing the PEAK button during Real Mode will bring up Peak Mode. Recorded

peak values for speed and engine speed will be displayed. Pressing the PEAK button

again during Peak Mode will return to Real Mode.

During either Real Mode or Peak Mode, the peak values will be reset by pressing and

holding the PEAK button for more than two seconds.

If Special Display Mode is turned on in the setting of special display and speed is

0km/h or 0MPH for more than 10 seconds in Real Mode, special display will start. In

this mode, the engine speed is displayed digitally. When speed is more than 0km/h or

0MPH or when any button of D.C.Unit is pressed, the display will return to Real Mode.

I)If the auto warning mode is turned ON in the setting of auto warning

NOTE: Even if REC button is pressed in vehicle's stopped condition, the vehicle speed data cannot be

recorded and Rec Mode will turn to Play Mode.

II)If the auto warning mode is turned OFF in the setting of auto warning

When the auto dimmer mode is selected in the setting of illumination control, the brightness of display is

adjusted automatically depending on the outside light. The brightness can be selected from three stages by

pressing the DIM(ENTER) button. When the manual dimmer mode is selected, the brightness of display is

fixed. The brightness can be selected from five stages by pressing the DIM(ENTER) button.

２. Opening and Ending Mode

３. Operation Mode

Manual dimmer mode

Auto dimmer mode

DARKBRIGHT

M-５ M-４ M-３ M-２ M-１

A-L３ A-L２ A-L１

NOTE: Once pause, fast-forward or rewind is performed with Defi-Link Control Unit II(or Defi-Link Control Unit), the

recorded speed data cannot be played back. To play back the speed data, Play Mode needs to be started

over again. Operation needs to be performed in vehicle's stopped condition. If the PLAY button is pressed

in vehicle's running condition, speed data will not be played back but Play Mode will turn to Rec Mode.

NOTE: The pulse free setting needs to be done again if units are changed.

NOTE: If the Defi-Link Display VSD CONCEPT is linked with the Defi-Link System, the setting of Defi-

Link Control Unit II(or Defi-Link Control Unit) is prioritized.

NOTE: This function operates when the Defi-Link Display VSD CONCEPT is linked with the Defi-Link

System and the temperature sensor is connected.

NOTE: This function operates when the Defi-Link Display VSD CONCEPT is linked with the Defi-Link

System and the temperature sensor is connected.

NOTE: If the Defi-Link Display VSD CONCEPT is linked with the Defi-Link System, the tachometer

warning2 cannot be set. The setting value of the tachometer warning of Defi-Link Control Unit

II(or Defi-Link Control Unit) is applied as a tachometer warning2. Please set up the tachometer

warning of Defi-Link Control Unit II(or Defi-Link Control Unit) higher than the tachometer

warning1 value. If the value is set lower than the warning1, the warning1 will be invalid.

NOTE: If the Defi-Link Display VSD CONCEPT is linked with the Defi-Link System, the warning buzzer

of Defi-Link Control Unit II cannot be absorbed.

NOTE: This function operates when the Defi-Link Display VSD CONCEPT is linked with the Defi-Link

System.

When the auto dimmer mode is on, the brightness of the display is adjusted automatically. Press

ENTER to Select one from three stages of brightness in the auto dimmer mode during the real mode or

the peak mode. When the manual dimmer mode is on, the brightness of the display can be set

manually at 5 stages in the real mode or the peak mode.

1 2 ... 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Defi Link VSD Concept User Manual Page 12

Comments to this Manuals